Fide Freight

Washington Oversize Load Regulations and Permits

Washington oversize rules: legal limits (8 ft 6 in wide, 14 ft high), pilot car certification, commute curfews, holiday limits and WSDOT permits.

Updated 9 min read

Legal width
8 ft 6 in
Legal height
14 ft
Semitrailer length
53 ft
Gross weight
Up to 105,500 lb
Set by axle count and spacing
First escort
Over 11 ft wide
Front and rear on two-lane highways
Superload from
Over 16 ft wide or high
Or over 125 ft trailer and load, or 200,000 lb
Night moves allowed
Up to 12 ft wide
And 14 ft 6 in high, 105 ft long
Holiday rule
From noon the day before
Six holidays, plus the day after Thanksgiving

Permits issued by

WSDOT Commercial Vehicle Services

Apply online
eSNOOPI Pro
Office hours
Mon–Fri 7:00 a.m.–4:00 p.m., closed noon–12:30 p.m.
On this page

In Washington, a truck and load can be 8 ft 6 in wide and 14 ft high without a permit, with a semitrailer up to 53 ft long. Legal gross weight runs up to 105,500 lb, depending on how many axles the rig has and how far apart they are. Anything bigger or heavier needs a special motor vehicle permit from the Washington State Department of Transportation (WSDOT), which you self-issue online in eSNOOPI Pro or order through WSDOT Commercial Vehicle Services at (360) 704-6340.

Two Washington rules need early planning. Escorts start at just over 11 ft wide on two-lane highways, and every pilot/escort vehicle operator must be certified. WSDOT also closes busy freeway sections around Seattle, Tacoma, Vancouver and Spokane during weekday commute hours to permit loads that need "OVERSIZE LOAD" signs.

Key points:

  • Pilot/escort operators need a Washington certificate. Drivers licensed in another state can instead use one from the eight states WSDOT accepts.
  • You can self-issue permits up to 16 ft wide, 16 ft high, 125 ft of trailer and load, and 200,000 lb. Anything larger is a superload that needs WSDOT's written approval.
  • Permit loads stay off state highways on six holidays and the day after Thanksgiving, starting at noon the day before.
  • A single-trip oversize permit costs $10. Overweight permits are priced per mile, with a $14 minimum.

These are the most a truck and load can measure and weigh on Washington public highways without a special permit, under chapter 46.44 of the Revised Code of Washington (RCW).

LimitLegal in WashingtonWhere it comes from
Width8 ft 6 inRCW 46.44.010
Height14 ft, with or without loadRCW 46.44.020
Semitrailer length53 ft in a tractor-semitrailer combination; only the trailer and load count unless the tractor also carries freightRCW 46.44.030; WSDOT Commercial Vehicle Guide
Doubles61 ft for the two trailers combinedRCW 46.44.030
Truck and trailer75 ft overallRCW 46.44.030
Single-unit truck length40 ftRCW 46.44.030
Load overhang3 ft past the front wheels or front bumper; 15 ft past the center of the last axleRCW 46.44.034
Gross weightUp to 105,500 lb, set by the weight table for the number of axles and the distance between themRCW 46.44.041
Axle weights20,000 lb single, 34,000 lb tandem; tires limited to 600 lb per inch of width, or 500 lb on an axle other than a steer axle that carries more than 10,000 lb on two tiresRCW 46.44.041; RCW 46.44.042

A truck can carry only the weight it's licensed for, even within the weight table. A combination licensed at 80,000 lb can add a temporary additional tonnage permit for at least five days, at $2.80 per day for each 2,000 lb (RCW 46.44.095).

The 14 ft legal height doesn't guarantee clearance. WSDOT makes overheight clearance the carrier's responsibility, so check bridge heights on the route.

How large a Washington oversize permit load can be

Washington's permit limits depend on the type of highway, and bridges, curves and overhead structures set most of the real maximums.

  • Width: on state highways outside cities and towns, up to 14 ft on two-lane highways, 20 ft on multilane highways with a median barrier and 32 ft on multilane highways without one (RCW 46.44.092). On a two-lane highway, a load up to 16 ft wide and 80,000 lb can move in daylight. WSDOT can allow more on highways built for it.
  • Height and length: there's no set maximum. Clearances, curves and ramps decide the route, and under Washington Administrative Code (WAC) 468-38-070 you must check or prerun it yourself.
  • Axle weights under an overweight permit: 22,000 lb on a single axle and 43,000 lb on a tandem 3 ft 6 in to under 7 ft apart. Longer groups depend on the spread from first to last axle: 6,500 lb per foot for 7 to under 10 ft, 2,200 lb times (spread plus 20) for 10 to under 30 ft, and 1,600 lb times (spread plus 40) at 30 ft or more (RCW 46.44.091). Tires carry no more than 600 lb per inch of width or their rating, whichever is lower.
  • Self-issue limits: in eSNOOPI Pro, you can self-issue a single-trip permit for a tractor-trailer, including jeeps and boosters, up to 16 ft wide, 16 ft high, 125 ft of trailer and load, and 200,000 lb gross. The permit covers one route-specific move and is valid for 3 days.

When a Washington load becomes a superload

WSDOT treats a non-divisible load as a superload when it weighs over 200,000 lb, is over 16 ft wide or 16 ft high, or has a trailing unit and load over 125 ft long (WAC 468-38-405). Superloads can't be self-issued. You send Commercial Vehicle Services a Request for Approval of Superload Movement (DOT Form 560-022), then apply for the permit once WSDOT approves it.

Washington's official sources give different lead times. Under RCW 46.44.091 and WAC 468-38-405, a load over 200,000 lb needs a written application at least 30 days ahead, and a load that's a superload only by size needs at least seven calendar days. WSDOT's permit types page, and the request form section of its superload page, ask for the request at least 30 days before any superload move, so plan on 30 days.

The request needs proof that the move is necessary, a sketch or photo showing why the item can't be split, and a sketch of the loaded rig with axle weights, spacings and tire sizes. It also needs a review of rail or barge options, a proposed route with any county or city approvals, and a traffic control plan. WSDOT then checks bridges and pavement and may ask you to share the cost of a long analysis. If a structure can't carry the load, WSDOT denies the request, and you need another route or rig.

Washington escort and pilot car requirements

WSDOT's escort triggers depend on the load's size and on whether the highway has two lanes or more (WAC 468-38-100).

LoadTwo-lane highwayMultilane highway
Over 11 ft to 14 ft wide1 front and 1 rearNo escort
Over 14 ft to 20 ft wide1 front and 1 rear1 rear
Over 20 ft wide1 front and 1 rear1 rear on divided highways; 1 front and 1 rear on undivided highways
Tractor-trailer with trailer and load over 105 ft1 rearNo escort
Tractor-trailer with trailer and load over 125 ft1 rear1 rear
Rear overhang over one-third of the trailer and load length1 rearNo escort
Front overhang over 20 ft from the steer axle1 frontNo escort
Rear overhang over 20 ft on a single-unit truck1 rearNo escort
Over 14 ft 6 in high1 front with a height pole1 front with a height pole, plus 1 rear if over 12 ft wide
Driver can't see 200 ft behind the rig in the mirrors1 rear1 rear

For the 105 ft and 125 ft length triggers and the one-third rear overhang trigger, the permit can allow a riding flag person instead of a pilot/escort vehicle. WSDOT can also require escorts for any load when it decides the public needs them.

Washington requires certified pilot/escort vehicle operators. A driver with a Washington license must carry a Washington certificate card while escorting. Drivers licensed elsewhere can get the Washington card or use a certification from a state WSDOT accepts: as of November 2026, Arizona, Colorado, Georgia, Minnesota, North Carolina, Oklahoma, Utah and Virginia. The Washington card takes an eight-hour course and a written test passed with at least 80%, and it's renewed every three years.

Washington pilot/escort vehicles must:

  • be a passenger car, van or two-axle truck of 16,000 lb gross or less, 60 to 102 in wide, towing nothing;
  • show a roof-mounted "OVERSIZE LOAD" sign at least 5 ft wide and 10 in high, with 8 in black letters on yellow, and an amber light above the roof that's visible from 500 ft all around;
  • keep two-way radio contact with the truck, and carry a STOP/SLOW paddle, three reflective triangles, a fire extinguisher, a hard hat and a high-visibility garment;
  • for loads over 14 ft 6 in high, mount a nonconductive height pole on the lead vehicle, set 3 to 6 in above the load.

For-hire operators also need commercial auto insurance of at least $100,000 per person and $300,000 per accident for bodily injury, and $50,000 for property damage.

When Washington requires a police escort

Washington sets no fixed size that triggers a police escort. For a superload, WSDOT can require extra pilot/escort vehicles or law enforcement vehicles, depending on the load's size, the route and the time of day (WAC 468-38-405).

When oversize loads can move in Washington

Washington permit loads move in daylight unless they fit the night envelope or the permit approves night travel.

  • Daylight: from 30 minutes before sunrise to 30 minutes after sunset.
  • At night: a load up to 12 ft wide, 14 ft 6 in high and 105 ft long, including legal overhang, can move at night. A larger load needs "Nighttime movement approved" on the permit. Night moves still follow the commuter curfews and need proper lighting.
  • Weekends: chapter 468-38 WAC sets no weekend ban, and commuter curfews apply Monday through Friday only.
  • Weather: no permit moves when visibility is 1,000 ft or less. Permit loads can't enter areas signed "TRACTION ADVISORY OVERSIZE VEHICLES PROHIBITED," "VEHICLES OVER 10,000 GVWR CHAINS REQUIRED" or "ALL VEHICLES CHAINS REQUIRED EXCEPT ALL-WHEEL DRIVE."

Some loads are exempt from the holiday and commuter limits (WAC 468-38-075). They include a single trailer up to 56 ft with its load, a non-divisible load up to 61 ft including its trailer, and overweight-only loads at legal dimensions that keep up with posted speeds.

Washington holiday restrictions

Permit loads can be kept off state highways on New Year's Day, Memorial Day, Independence Day, Labor Day, Thanksgiving Day and the day after, and Christmas Day, starting at noon the day before each holiday (WAC 468-38-175). WSDOT's permit conditions apply the ban to all over-dimensional loads and to overweight loads that can't keep up with traffic.

For the next three holidays, that means no permit moves from noon Wednesday, November 25, through Friday, November 27, 2026; from noon Thursday, December 24, through Friday, December 25, 2026; and from noon Thursday, December 31, 2026, through Friday, January 1, 2027.

Washington commuter curfews

WSDOT closes these Interstate and state route (SR) sections on weekdays to permit loads that must display "OVERSIZE LOAD" signs. A load that's over width only, and no wider than the width shown, is exempt, and overweight doesn't count unless the truck can't keep up with traffic. These were the curfews as of November 20, 2026.

AreaHighway sectionsWeekday curfew hoursWidth-only loads exempt up to
Seattle and EverettI-5 from SR 512 to SR 531; all of I-405; I-90 from I-5 to the Sunset Interchange; parts of SR 2, 18, 167, 518 and 522Between 6 and 9 a.m. and between 3 and 7 p.m., by segment and direction10 ft; 9 ft on SR 2 and on I-5 from SR 599 to SR 523
TacomaI-5 from Exit 118 to SR 512; SR 16; SR 512Between 6 and 9 a.m. and between 3 and 7 p.m., by segment and direction10 ft
OlympiaI-5 from Exit 99 to Exit 1094 to 6 p.m.10 ft
VancouverI-5 from the Oregon line to I-205; I-205 from the Oregon line to I-5Southbound 6 to 9 a.m.; northbound 3 to 6 p.m. on I-5 and 4 to 7 p.m. on I-20510 ft
KelsoSR 433, Lewis and Clark Bridge6 to 9 a.m.10 ft
SpokaneI-90 from Medical Lake to Liberty Lake6 to 9 a.m. and 3 to 7 p.m.11 ft 2 in

Check the segment-by-segment times on WSDOT's curfew hours and holiday restrictions page before the move.

How to get a Washington oversize permit

Washington permits are self-issued in eSNOOPI Pro (Electronic System Network for Oversize and Overweight Permit Information Pro) or bought through WSDOT and its agents.

  1. Measure first. You need the width, height, length, overhangs, axle weights and axle spacings. Overweight permits need an axle spacing report number from WSDOT.
  2. Set up an account. In eSNOOPI Pro, choose "Create New Account" and accept the terms of service. If your company's USDOT number is already registered, your self-issue supervisor adds new users.
  3. Apply. Self-issued permits issue instantly, 24 hours a day. Requests that need WSDOT approval, such as night moves outside the envelope, take up to 3 business days. WSDOT-authorized permit agents and WSDOT offices also sell permits. WSDOT offices take cash or check only, and ports of entry don't sell permits.
  4. Check the route. You supply the route and check its restrictions and clearances. The state permit covers state highways only, so county roads and city streets need local approval.
  5. Carry the permit. Keep the signed permit in the power unit, on paper or on a screen at least 3.5 by 5 in for a routed permit. Signing it confirms at least $750,000 in liability insurance.

Washington oversize permit fees

Washington's permit fees are set by statute in RCW 46.44.0941.

Permit or feeAmount
Single-trip permit, oversize only (3 days)$10
Overweight permit7 cents per mile for up to 9,999 lb over legal capacity, rising to $4.25 per mile at 100,000 lb over; minimum $14
30-day over-width or over-height permit (non-divisible, up to 14 ft wide and 15 ft high)$20
30-day over-length permit (non-divisible, up to 125 ft)$10
Duplicate permit$14

Above 100,000 lb over legal capacity, the overweight fee adds 50 cents for each further 5,000 lb or part of it. A load that's both oversize and overweight pays only the overweight fee (RCW 46.44.096).

Planning an oversize move through Washington

Washington's 14 ft legal height, 8 ft 6 in width and 53 ft semitrailer limit match Oregon's, though Oregon allows a 53 ft trailer only on its Group 1 highways and designated routes. Idaho also allows 14 ft and 8 ft 6 in, but its 53 ft semitrailer applies on the National Network and approved state highways, with 48 ft elsewhere. British Columbia's height limit is lower, at 4.15 m (about 13 ft 7 in) without a permit, so a 14 ft load that's legal in Washington needs a B.C. permit. Compare every leg in our Oregon oversize permit guide, our Idaho oversize permit guide and the legal limits in all 50 states.

Check pilot car certification when you book escorts. Oregon's pilot vehicle rule, Oregon Administrative Rule (OAR) 734-082-0035, requires no general operator certificate, and WSDOT's accepted list doesn't include Oregon or Idaho. Make sure every escort operator on the Washington leg holds a Washington card or one from a listed state.

Lead time comes down to the self-issue limits. A load within 16 ft wide, 16 ft high, 125 ft of trailer and load and 200,000 lb can be self-issued instantly, while a superload needs WSDOT's written approval and, to be safe, 30 days. Time departures around the weekday curfews near Seattle, Tacoma, Vancouver and Spokane. In winter, a permit load can't cross a mountain pass while traction or chain restrictions are posted.

Moving a load into, out of or across Washington? Request a heavy haul quote with the dimensions, weight and route, or see our over dimensional freight service.

Sources

Official sources, each checked on November 20, 2026.

  1. 1.WSDOT: Commercial vehicle permits
  2. 2.WSDOT: Self-issue a permit (eSNOOPI Pro permit types, limits and fees)
  3. 3.WSDOT: Permit types & fees
  4. 4.WSDOT: Superloads
  5. 5.WSDOT: Pilot & escort vehicle (partner certification states)
  6. 6.WSDOT: Curfew hours & holiday restrictions
  7. 7.WSDOT: Permit contacts
  8. 8.WSDOT: Permit offices (WSDOT offices and authorized permit agents)
  9. 9.WSDOT: Special Motor Vehicle Permit Regulations and Conditions (DOT Form 560-002, revised July 2023)
  10. 10.WSDOT: Washington State Commercial Vehicle Guide (M 30-39.10, July 2025)
  11. 11.Washington State Legislature: Chapter 46.44 RCW: Size, Weight, Load (§§ 46.44.010 to 46.44.096)
  12. 12.Washington State Legislature: Chapter 468-38 WAC: Vehicle Size and Weight (§§ 468-38-005, -050, -070, -075, -095, -100, -155, -175 and -405)
  13. 13.ODOT: Group Map 1 designations list and legend, with Oregon legal lengths by highway group (form 735-8100)
  14. 14.Oregon Secretary of State: OAR 734-082-0035: Pilot Vehicle(s)
  15. 15.Province of British Columbia: Commercial Transport Regulations, B.C. Reg. 30/78, Division 7 (§§ 7.05 and 7.06)

Fide Freight is a member of the Specialized Carriers & Rigging Association (SC&RA).

Oversize load in Washington? We'll plan it.

Permits, escorts, route surveys and specialized trailers, planned state by state and priced in one quote.