In Idaho, a truck and load can be 8 ft 6 in wide, 14 ft high and 80,000 lb gross on Interstates without a permit, or up to 105,500 lb on other highways when the axle spacing allows. A semitrailer can be 53 ft long on the National Network and approved state highways, 48 ft elsewhere. Anything larger needs a special permit from the Idaho Transportation Department (ITD), ordered in its ITRPS system at Permits4Idaho.com or by phone at (208) 872-3163.
Idaho's oversize rules run on a color-coded map. ITD's Pilot/Escort Vehicle Travel and Vertical Clearance of Structures Map marks every state highway red, black or white (the Interstates), and the color sets your escorts and travel hours. Red routes carry the strictest limits: oversize loads move there in daylight on weekdays only, and stop at 2 p.m. on Fridays. An ITD permit covers state highways only, so county and city roads need their own approval unless the local agency has an agreement with ITD.
Key points:
- Escorts start just over 8 ft 6 in wide on red routes, over 12 ft wide on black routes and over 15 ft wide on Interstates.
- On black routes and Interstates, loads up to 12 ft wide, 120 ft long and 15 ft high can move around the clock. Larger loads move in daylight only.
- Loads more than 13 ft wide can't move from 6 to 9 a.m. or 4 to 6:30 p.m. on weekdays in 10 listed areas, including the Boise valley, Coeur d'Alene, Idaho Falls, Pocatello and Twin Falls.
- A single-trip permit costs $30 for oversize and $33 plus a per-mile road use fee for overweight. A bridge analysis takes up to 3 business days, or up to 10 above 250,000 lb.
Idaho legal limits without a permit
These are the most a truck and load can measure and weigh on Idaho highways without a special permit.
| Limit | Legal in Idaho | Where it comes from |
|---|---|---|
| Width | 8 ft 6 in, including the load | Idaho Code § 49-1010(1) |
| Height | 14 ft, including the load | Idaho Code § 49-1010(2) |
| Semitrailer length | 53 ft on the National Network, access routes within 1 road mile of it and state highways the Idaho Transportation Board approves; 48 ft elsewhere | Idaho Code § 49-1010(3)(b) |
| Overall length | 75 ft for a motor vehicle and one or more trailers. On routes the board restricts for severe curves, deficient width or heavy traffic, semitrailer combinations are limited to 65 ft overall | Idaho Code § 49-1010(3)(b) and (c) |
| Single truck length | 45 ft | Idaho Code § 49-1010(3)(a) |
| Load overhang | 4 ft past the front, 10 ft past the rear | Idaho Code § 49-1010(4) |
| Gross weight | 80,000 lb on Interstates; up to 105,500 lb on other highways, within the axle-spacing table | Idaho Code § 49-1001 |
| Axle weights | 20,000 lb single axle, 34,000 lb tandem, 10,000 lb per wheel | Idaho Code § 49-1001 |
The 105,500 lb figure applies only off the Interstate, and only when the axle groups and spacing meet the § 49-1001 table. A divisible load between 105,501 and 129,000 lb needs an annual extra length/excess weight permit and must stay on ITD's designated routes up to 129,000 lb.
How large an Idaho oversize permit load can be
Idaho's rules set no fixed maximum size for a single-trip permit. Under ITD's special permit rule, IDAPA 39.03.01, the largest load depends on the route's width, alignment, sight distance, clearances and traffic.
- Annual oversize permits: up to 16 ft wide, 15 ft 6 in high and 120 ft long, including overhang, on black routes and Interstates. On red routes, annual permits stop at 12 ft 6 in wide.
- Extra approval: ITD needs additional approval, which can take up to 24 working hours, for a load over 16 ft wide on red or black routes, 18 ft wide on an Interstate, 16 ft high on any route, 120 ft long off the Interstate or 150 ft long on it.
- Height: every over-height permit depends on the clearances along the route, and ITD may take at least 24 working hours to evaluate one. Over 16 ft 6 in, you must contact the utility companies about power lines, and advance notice may be needed where the route passes under traffic signals.
- Traffic control plan: on a two-lane highway, a load over 18 ft wide, 150 ft long or 16 ft high needs a traffic control plan. A licensed engineer or a traffic control supervisor certified by the American Traffic Safety Services Association (ATSSA) must prepare it.
- Overweight loads: the weight must be reduced to a practical minimum, and the hauling vehicle needs five or more axles. Self-propelled vocational vehicles and vehicles towing an overweight load are excepted. No tire can carry more than 800 lb per inch of width.
When an Idaho load becomes a superload
Idaho's rules don't use the term superload. A heavy Idaho load instead triggers a bridge review, and that review sets your lead time.
- Axle weight: any single axle or steer axle over 35,000 lb needs bridge approval.
- Analysis time: ITD can take up to 3 business days to analyze a vehicle up to 250,000 lb and up to 10 business days above that. Reviewing an analysis done by a third party also takes up to 10 business days.
- Third-party analysis: a vehicle over 800,000 lb needs a pre-approved third party to do the bridge analysis, at your cost, before ITD reviews it. The same applies when you ask ITD to compare several vehicle configurations or several routes.
- Annual overweight levels: annual permits follow the colors on ITD's Route Capacity Map, a separate map from the escort map. Levels run from 22,500 lb single, 38,000 lb tandem and 48,000 lb tridem on yellow routes up to 33,000 lb, 56,000 lb and 70,500 lb on black routes. A load above those levels needs a single-trip permit.
Idaho escort and pilot car requirements
Idaho escort requirements depend on the route's color on ITD's Pilot/Escort Vehicle Travel and Vertical Clearance of Structures Map, dated January 8, 2025. The map gives these triggers.
| Route | Load | Escorts |
|---|---|---|
| Red | 8 ft 7 in to 10 ft wide | 1 front |
| Red | 10 ft 1 in to 12 ft 6 in wide | 1 front and 1 rear |
| Red | Over 75 ft long | 1 front |
| Red | Over 75 ft long and 8 ft 7 in to 12 ft 6 in wide | 1 front and 1 rear |
| Black | 8 ft 7 in to 12 ft wide | None |
| Black | 12 ft 1 in to 14 ft wide | 1 front |
| Black | 14 ft 1 in to 18 ft wide | 1 front and 1 rear |
| Black | Over 120 ft long, up to 12 ft wide | 1 front |
| Black | Over 120 ft long and 12 ft 1 in to 18 ft wide | 1 front and 1 rear |
| White (Interstate) | 8 ft 7 in to 15 ft wide | None |
| White (Interstate) | 15 ft 1 in to 18 ft wide | 1 rear |
A load over 16 ft high needs a lead escort with a non-metallic height pole. A single-trip permit lists the escorts you must use in its escort and restriction sections; annual permit holders follow the map. ITD can also require a third escort to hold oncoming traffic at turnouts and intersections when a load is extreme for the route.
Idaho escort vehicles must:
- be a passenger car or truck of 16,000 lb or less, not towing a trailer;
- show an "OVERSIZE LOAD" roof sign 12 in high and 5 ft wide, with 8 in black letters on yellow, only while escorting;
- run flashing or rotating amber lights at each end of the sign, or one amber beacon visible from 500 ft, with headlights and taillights on;
- keep two-way radio contact with the truck over at least half a mile, and stay about 1,000 ft from the load in rural areas;
- carry an 18 in STOP/SLOW paddle, three reflective triangles, a 5 lb fire extinguisher, an ANSI Class 2 or 3 vest (Class 3 at night), two spare signs, a hard hat, a flashlight, a first aid kit and, when required, a non-conductive height pole.
Idaho's rule sets vehicle and equipment standards for escorts but no pilot car driver certification. The escort driver needs a valid driver's license.
When Idaho requires a police escort
Idaho's special permit rule sets no statewide trigger for a police escort. The exception is US 12 from milepost 74 to 174, through the Nez Perce–Clearwater Forest, where a federal court decision gave the U.S. Forest Service oversight of oversize loads. The Forest Service reviews any load there that is over 16 ft wide, 150,000 lb or 150 ft long, needs more than 12 hours to make the trip, or requires changes to the road or roadside vegetation.
Those US 12 loads need a safety inspection by the Idaho State Police, or an equivalent agency in another state, before the permit issues. They also need ambulances, and possibly law enforcement escorts. ITD allows only one such load on that stretch at a time and sets travel times by traffic volume, which can mean night moves or no weekend and holiday travel.
When oversize loads can move in Idaho
Idaho's travel hours depend on the load's size and the route's color.
- Black routes and Interstates: loads up to 12 ft wide, 120 ft long and 15 ft high can move 24 hours a day, 7 days a week. Larger loads move in daylight only, weekends included.
- Red routes: oversize loads move in daylight, Monday through Friday, and stop at 2 p.m. on Fridays. Travel resumes at sunrise on Monday. A single-trip permit can set other hours.
- Night lighting: an over-width load moving from 30 minutes after sunset to 30 minutes before sunrise, or in visibility under 500 ft, needs amber lights at its front extremities and red lights at the rear.
- Front overhang: more than 7 ft of front overhang limits a permit load to daylight on two-lane, two-way highways.
- Weather: a permit becomes invalid en route in winds over 40 mph, in visibility under 500 ft, when ice, snow, frost, standing water or mud cost traction, or when the 511 traveler system marks the road "Difficult".
- Spring breakup: ITD can post axle limits of 16,000, 14,000 or 12,000 lb. On posted two-lane sections, permit loads are capped at 12 ft 6 in wide.
Idaho holiday restrictions
Idaho's permit holidays are New Year's Day, Memorial Day, Independence Day, Labor Day, Thanksgiving and Christmas. On red routes, travel stops at 2 p.m. the day before the holiday. On black routes and Interstates, loads over 12 ft wide, 120 ft long or 15 ft high stop at 4 p.m. the day before. Both resume at sunrise the day after the holiday, except that red routes stay closed on weekends.
For Thanksgiving 2026, restricted loads stop at 2 p.m. or 4 p.m. on Wednesday, November 25, and restart at sunrise on Friday, November 27. Red-route loads can then move only until 2 p.m. that Friday. Christmas Day and New Year's Day fall on Fridays, so travel stops on Thursday, December 24 and Thursday, December 31. Black-route and Interstate loads restart on Saturday, December 26 and Saturday, January 2, 2027. Red-route loads wait until Monday, December 28 and Monday, January 4. ITD's offices are closed on Thanksgiving Day, Christmas Day and New Year's Day.
Idaho commuter-hour restrictions
Loads more than 13 ft wide can't move on state highways from 6 to 9 a.m. or 4 to 6:30 p.m. local time, Monday through Friday, in the areas below. Smaller permit loads moving at those times keep to the far right lane.
| Area | Restricted section |
|---|---|
| Boise valley | I-84, mileposts 26 to 59 |
| Coeur d'Alene | I-90, mileposts 0 to 17 |
| Idaho Falls | I-15, mileposts 115 to 121 |
| Pocatello valley | I-15 mileposts 67 to 74; I-15B mileposts 0 to 5.5; I-86 mileposts 58 to 63; US 30 mileposts 331 to 336; US 91 mileposts 77 to 82 and 100 to 103 |
| Twin Falls | US 93, mileposts 41 to 53 |
| Eagle, Emmett, Garden City, Middleton and Star | Within 1 mile of the city limits |
How to get an Idaho oversize permit
Idaho special permits are ordered online in ITRPS, by phone or in person at a port of entry.
- Measure first. You declare the gross weight, axle weights and dimensions, and you're responsible for them. ITRPS has a permit wizard if you're not sure which permit fits.
- Set up an account. To create a new ITRPS customer account, with or without a USDOT number, call the permit office at (208) 872-3163.
- Apply before the load moves. Idaho law requires a permit, or a permit number from a permit office, before an oversize or overweight vehicle enters the highway. Every vehicle under the permit also needs a valid annual inspection.
- Pay. Fees are due when the permit issues. ITD refunds a fee only if you contact Commercial Vehicle Services within 2 working days after the permit's start date, or if ITD issued it in error.
- Carry and follow the permit. Keep it in the truck, on paper or electronically. Every oversize vehicle must stop at every port of entry for inspection.
Idaho oversize permit fees
ITD's permit fees are set in IDAPA 39.03.01, with a road use fee on top for overweight loads.
| Permit or fee | Amount |
|---|---|
| Single-trip permit, oversize only | $30 |
| Single-trip permit, overweight or overweight and oversize (non-divisible) | $33 plus road use fee per mile |
| Annual overweight/oversize permit (non-divisible) | $128 |
| Annual extra length/excess weight permit, divisible loads up to 129,000 lb | $45 |
| Eastport/Canadian weight permit | $45 |
| Permit reissue or transfer | $15 |
Annual permits bought online cost $5 less. The road use fee depends on gross weight and axle count (Idaho Code § 49-1004(2)). For a five-axle combination, it starts at 4 cents a mile at 80,001 lb and rises 4 cents for each 2,000 lb. At 118,001 to 120,000 lb, that comes to 80 cents a mile. Annual overweight permit holders report their loaded miles to ITD every quarter, even when they drove none.
Planning an oversize move through Idaho
Idaho's 53 ft semitrailer limit matches Washington, Oregon (on its Group 1 highways and designated routes), Nevada, Utah and Montana, but it's 7 ft shorter than Wyoming's 60 ft. Montana allows up to 57 ft with a term permit. All six neighbors share Idaho's 8 ft 6 in width and 14 ft height. Inside Idaho, a 53 ft trailer is legal only on the National Network and approved state highways, so check the last miles to the job site. See legal limits in all 50 states, and the Wyoming and Utah guides for the next states east and south.
Route color drives most Idaho plans. A 13 ft wide load needs no escort on I-84, needs one front escort on a black state highway, and falls outside the red-route chart, which stops at 12 ft 6 in. Lead time comes from ITD's extra approval for loads over 16 ft wide (18 ft on Interstates) or 16 ft high, bridge analysis on heavy loads, and Forest Service review on US 12. In spring, breakup postings can also cut permit widths to 12 ft 6 in on two-lane roads.
Moving a load into, out of or across Idaho? Request a heavy haul quote with the dimensions, weight and route, or see our over dimensional freight service.
